HP OMNIBOOK 600 - CONFIGURATION FILES FOR THE OLICOM TOKEN RING PCMCIA

PC CARD



          

          Disclaimer:The products listed are not

                    products of the Hewlett-Packard Company,

                    but rather products of third party

                    developers.  Such products have not been

                    fully tested and only partially

                    evaluated by HP, and are not endorsed,

                    warranted, or supported by HP.   HP

                    expressly disclaims all responsibility

                    and liability for the manufacturing,

                    distribution, marketing, licensing,

                    installation, use performance,

                    maintenance, and support of such

                    products.   Readers of this guide are

                    advised to make their own independent

                    verification of the information provided

                    for such products by third party

                    developers.

  



OB600 LAN CARD CONFIGURATION FILES

  

  The following contains the configuration information for the

  Olicom PCMCIA for Windows for Workgroup (NDIS) system.

  

          

          NOTE:Changes to the standard configuration

                    are indicated in bold characters.  The

                    pound signs should be removed and are

                    listed only to identify the changes.

  

  Only files that need to change are listed below.

  

  

  CONSIDERATIONS

  

     The Olicom drivers do not support hot swapping. Whenever the

     platform gets taken off the network the system will have to be

     rebooted to reinitialize the LAN.  This happens when the system

     enters suspend by pushing on "ON" key or timing out.

  

  

  ************************ NDIS ***********************

  



CONFIG.SYS

  

  REM

  REM CONFIG.SYS -- OmniBook default startup file for drive C

  REM

  

  [menu]

  menuitem=LapLink, Windows & LapLink

  menuitem=Windows, Windows only

  menuitem=MS-DOS, MS-DOS only -- Default

  menudefault=MS-DOS,3

  menucolor=2

  

  [LapLink]

  [Windows]

  [MS-DOS]

  lastdrive=p

  

  [common]

  shell=c:\command.com /p /e:2048 c:\

  device=c:\dos\himem.sys /machine:2 /testmem:off

  

  REM "X=" reserves memory for PCMCIA cards

  REM "I=" reserves remaining memory for UMBs

  rem device=c:\dos\emm386.exe noems i=b000-b7ff i=c000-d3ff x=d400-

       e7ff

  device=c:\dos\emm386.exe noems x=d000-dfff

  

  dos=high,umb

  devicehigh=c:\dos\power.exe

  

  

  REM OmniBook Socket Services 2.1 driver required for card slot

       support

  

  devicehigh=c:\cardsoft\obss.exe

  

  REM Card Services 2.1 driver required for card slot support

  

  devicehigh=c:\cardsoft\cs.exe /systemsoft1=1

  

  REM Card Services APM support required for card slot support

  

  install=c:\cardsoft\cs_apm.exe

  

  REM Initial resource allocator required for card slot support

  

  device=c:\cardsoft\csalloc.exe

  

  REM ATA card driver required for ATA cards

  rem devicehigh=c:\cardsoft\atadrv.exe /s:2

  

  REM Driver required for RAM cards

  rem devicehigh=c:\cardsoft\mtsram.exe

  

  REM Memory card driver required for all memory cards

  REM If this driver not installed, remove /s:2 from the ATA card

       driver line

  rem devicehigh=c:\cardsoft\mtddrv.exe

  

  rem olicom card

  device=c:\olicom\octenabl.dos io=320 mw=D4

  

  REM Card identification driver required for cards other than memory

       cards

  devicehigh=c:\cardsoft\cardid.exe

  

  REM OBMGM must be installed for the system to operate properly...

  rem install=c:\omnibook\obmgm.com   /c

  install=c:\omnibook\obmgm.com

  

  buffers=10,0

  files=30

  

  REM LASTDRIVE=Y leaves one drive letter available for Novell

       networks...

  lastdrive=p

  FCBS=4,0

  

  REM OmniBook needs at least 12 stacks available...

  stacks=12,256

  

  REM IFSHLP is required by Windows for Workgroups

  device=c:\windows\ifshlp.sys

  [common]

  rem Environment variable to pass SCSI status to AUTOEXEC.BAT...

  set aspidock=1

  rem Enable SCSI (ASPI) manager...

  device=c:\scsi\aspi2dos.sys /d /z /q10

  REM To use a SCSI hard disk, remove "REM" from ASPIDISK line...

  REM device=c:\scsi\aspidisk.sys

  rem Enable SCSI CD-ROM driver...

  device=c:\scsi\aspicd.sys /d:aspicd0

  

  

  [common]

  



AUTOEXEC.BAT

  

  Only one change is required to autoexec.bat.

  

  Add

  

  NET START

  

  to somewhere in the top or bottom of the file.

  

  

  PROTOCOL.INI

  

  [network.setup]

  version=0x3110

  netcard=oli164ce,1,OLI164CE,1

  transport=ms$nwlinknb,NWLINK

  transport=ms$ndishlp,MS$NDISHLP

  transport=ms$netbeui,NETBEUI

  lana0=oli164ce,1,ms$netbeui

  lana1=oli164ce,1,ms$nwlinknb

  lana2=oli164ce,1,ms$ndishlp

  

  

  [protman]

  DriverName=PROTMAN$

  PRIORITY=MS$NDISHLP

  

  [OLI164CE]

  DriverName=OLITOK$

  IoAddress=0x0320

  MaxRequests=6

  MaxTransmits=6

  RecBufSize=1016

  RecBufCount=5

  MaxFrameSize=4060

  EarlyRelease=yes

  ReOpen=no

  FrameStatus=no

  NDIS201

  

  [NWLINK]

  

  BINDINGS=OLI164CE

  [MS$NDISHLP]

  DriverName=ndishlp$

  BINDINGS=OLI164CE

  

  [NETBEUI]

  DriverName=netbeui$

  SESSIONS=10

  NCBS=12

  BINDINGS=OLI164CE

  LANABASE=0

  



CARDID.INI

  

  No changes necessary to this file.

  

  ************  END of Olicom Token Ring configuration files for the

  OB600 ****************

  

                  Copyright  Hewlett-Packard Co. 1996

       This information is subject to change without notice and

                 is provided "as is" with no warranty.

          Hewlett-Packard shall not be liable for any direct,

        indirect, special, incidental or consequential damages

             in connection with the use of this material.